manualshive.com logo in svg

SEW-Eurodrive DHE21B, Manual, Page: 48 / 80

Share
Download
SEW-Eurodrive DHE21B Manual Download Page 48

48

Manual – Controllers DHE/DHF/DHR21B (standard) and DHE/DHF/DHR41B (advanced)

4

Installing the DHR21B/41B option

Assembly and Installation Notes

Changing the IP 
address parame-
ters after success-
ful initial startup

If the DHR21B/41B was started using a valid IP address, you can also access the IP
address parameters via Ethernet interface.

You can change the IP address parameters via Ethernet by one of the following
methods: 

•

Using the MOVITOOLS

®

 MotionStudio software

•

Using the EtherNet/IP TCP/IP interface object (see section "EtherNet/IP CIP object
directory")

•

Using the SEW Address Editor

You can also change IP address parameters via the other interface of the DHR21B/41B
option.

If the IP address parameters are assigned to the DHR21B/41B option by a DHCP
server, you can only change the parameters by adjusting the settings of the DHCP
server.

The methods listed above for changing the IP address parameters only come into effect
once the supply voltage (DC 24 V) has been switched off and back on again.

Deactivating/
activating the 
DHCP

The type of IP address allocation is determined by the setting of the attribute

Configuration Control

 of the EtherNet/IP TCP/IP interface object. The value is displayed

or modified in the 

P785 DHCP/Startup Configuration

 parameter.

•

"Stored IP parameters" setting

The stored IP address parameters are used.

•

"DHCP" setting

The IP address parameters are requested by a DHCP server.

If you use the DHCP server from Rockwell Automation, you can activate or
deactivate the DHCP by clicking a button. In this case, an EtherNet/IP telegram is
sent to the TCP/IP interface object of the station that is being addressed.

Resetting IP 
address 
parameters

If you do not know the IP address parameters and there is no serial interface or DBG60B
keypad for reading the IP address, you can reset the IP address parameters to the
default values using the DIP switch "2

0

".

This action resets the DHR21B/41B option to the following default values:

•

IP address: 192.168.10.4

•

Subnet mask: 255.255.255.0

•

Default gateway: 192.168.10.4

•

DHCP / Startup Configuration: Stored IP parameters (DHCP is disabled)

Proceed as follows to reset the IP address parameters to the default values:

•

Switch off the 24 V DC supply voltage and the line voltage.

•

On the DHR21B/41B option, set DIP switch "2

0

" to "1" (= right = ON).

•

Switch the DC 24 V supply voltage and the line voltage back on.

 

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for DHE21B

















































































Reviews:

No comments