manualshive.com logo in svg

SEW-Eurodrive DHE21B, Manual, Page: 41 / 80

Share
Download
SEW-Eurodrive DHE21B Manual Download Page 41

Manual – Controllers DHE/DHF/DHR21B (standard) and DHE/DHF/DHR41B (advanced) 

41

4

Installing the DHR21B/41B option

Assembly and Installation Notes

DIP switch 2

1

 

(protocol)

DIP switch "2

1

" is used to set the fieldbus protocol that is currently used.

•

2

1

 = "1" (= right = ON): The EtherNet/IP / Modbus TCP/IP fieldbus protocol is active

•

2

1

 = "0" (= left = OFF): The PROFINET fieldbus protocol is active.

4.9.4

The integrated Ethernet switch

You can use the integrated Ethernet switch to achieve line topologies known from the
fieldbus technology via X30-1 and X30-2. Other bus topologies, such as star or tree, are
also possible. Ring topologies are not supported.

Auto-crossing

The two ports leading out of the Ethernet switch have auto-crossing functionality. This
means that they can use both patch and cross-over cables to connect to the next
Ethernet station.

Auto-negotiation

The baud rate and the duplex mode are negotiated by both Ethernet nodes when
establishing the connection. For this purpose, both Ethernet ports of the EtherNet/IP
connection support an auto-negotiation functionality and work with a baud rate of either
100 Mbit or 10 Mbit in full duplex or half-duplex mode.

Notes on multicast 
handling

•

The integrated Ethernet switch does not provide a filter function for Ethernet
multicast telegrams. Multicast telegrams that are usually sent in Ethernet/IP
networks from the adapters to the scanners (PLC) are passed on to all switch ports.

•

IGMP snooping (managed switch) is not supported.

•

SEW-EURODRIVE therefore recommends to connect the DHR21B/41B option in
EtherNet/IP networks only with network components that support IGMP snooping
(e.g. managed switch) or that have safety mechanisms integrated against excess
multicast load (e.g. units from SEW-EURODRIVE). Units that do not have this
integrated function can fail due to high network loads. This restriction does not apply
to PROFINET IO or Modbus/TCP networks.

INFORMATION

The number of industrial Ethernet switches connected in line impacts the telegram
runtime. If a telegram passes through the units, the telegram runtime is delayed by the
store & forward function of the Ethernet switch:

•

For a telegram length of 64 bytes by approximately 10 µs (at 100 Mbit/s)

•

For a telegram length of 1500 bytes by approximately 130 µs (at 100 Mbit/s)

This means that the more units a telegram has to pass through, the higher the
telegram runtime is.

 

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for DHE21B

















































































Reviews:

No comments