manualshive.com logo in svg

SEW-Eurodrive DHE21B, Manual, Page: 5 / 80

Share
Download
SEW-Eurodrive DHE21B Manual Download Page 5

Manual – Controllers DHE/DHF/DHR21B (standard) and DHE/DHF/DHR41B (advanced)

5

Contents

5.3

Connection mode ...................................................................................... 52

5.3.1

Overview.................................................................................... 52

5.3.2

Selecting the communication mode (online or offline) ............... 53

5.4

Communication via USB ........................................................................... 54

5.4.1

Connecting the unit with the PC via USB .................................. 54

5.4.2

Installing the driver..................................................................... 55

5.4.3

Configuring USB communication............................................... 56

5.4.4

USB communication parameters ............................................... 57

5.5

Communication via Ethernet ..................................................................... 58

5.5.1

Direct communication ................................................................ 58

5.5.2

Address Editor ........................................................................... 59

5.5.3

Configuring the communication channel via Ethernet ............... 62

5.5.4

Setting communication parameters for SMLP ........................... 64

5.5.5

Communication parameters for SMLP....................................... 65

5.5.6

Communication ports used ........................................................ 65

5.6

Executing functions with the units ............................................................. 66

5.6.1

Parameterizing units .................................................................. 66

5.6.2

Reading or changing unit parameters........................................ 66

5.6.3

Starting up units (online)............................................................ 67

5.7

Configuration and startup of the drives ..................................................... 68

5.8

Configuration and startup in the PLC Editor ............................................. 68

5.9

Replacing the unit ..................................................................................... 68

6

Error Diagnostics .............................................................................................. 69

6.1

Diagnostic procedure CAN 1/CAN 2 system bus...................................... 69

7

Technical Data and Dimension Drawings ....................................................... 70

7.1

General technical data .............................................................................. 70

7.2

DHE21B/41B option .................................................................................. 71

7.3

DHF21B/41B option .................................................................................. 73

7.4

DHR21B/41B option.................................................................................. 74

7.5

Stand-alone unit ........................................................................................ 74

7.6

Dimension drawings for stand-alone unit DH.21B/41B/UOH..B ............... 75

7.6.1

Dimension drawing for DHE21B/41B / UOH11B ....................... 75

7.6.2

Dimension drawing for DHF/DHR21B/41B / UOH21B............... 76

Index................................................................................................................... 77

 

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Summary of Contents for DHE21B

















































































Reviews:

No comments