background image

 

 

 

 

       

 

 

 

 

           

 

SENSORPROX 100R/PIN120 - 

SINGLE DOOR CONTROLLER 

 

 

 

 

 

 

 

 

3. FEATURES 

 
- Single Door Controller 

- Built-in Proximity Reader with up to 10cm read range with IDC170 card 
- 512 Users or Card IDs including the Configuration card 

- 5 independent input ports 
- 4 output ports including 2 Form-C Relays to facilitate either Power-Failed Safe or Secure mode of operation 

- All I/Os behaviors and associated Timers are user programmable either through the keypad or the application software 
- Door Lock and Unlock functions 

- Configurable for Normal/Secure mode of operation (Secure Mode requires using external sensor(s) and alarm/siren) 
- Covert Duress sensing and responding (activate a silent alarm through the external Auto-Dialer) 

- Programmable On/Off audio feedback (turning off audio feedback for Silent mode of operation) 
- Programmable the maximum number of unsuccessful attempts allow before activating the Alarm when exhaustive break-in method 

is employed 

- RS-232 communication port for interfacing with the SENSORPROX 100R/PIN120 application software 

- 3 LEDs (red, green, and yellow) for system operation status 
- Chime Bell function to operate an externally connected Doorbell 

 
 

 
 

4. SPECIFICATION 

 
 

.Memory   

 

 

: Flash, Non-volatile, 1 millions times read/write 

 

.Power   

 

 

: DC 12V/ 200mA max. 

 .Proximity 

reader 

  : 

Built-in 

Proximity 

reader with up to 10cm read range with IDC170 

card 

.User capacity 

 

 

: 512 Users including the Configuration card 

 

.Input/Output 

 

 

: 5 Inputs, max. rating at DC12V/20mA 
: 2 Relay outputs : DC12V~24V/2A max. 

: 1 chime bell output : DC5V/150mA max. 
: 1 TTL output : DC5V/20mA   

 

.Communication 

 

 

: One RS-232 port, 9600 Baud Rate,N,8,1, Xon and Xoff 

 .Keypad 

   : 

12 

Numeric 

Keypad 

 

.LED 

 

 

 

: 3 LEDs (red, green, and yellow) 

 

.Operating environment range 

: -35

°

C to +65

°

C, 10% to 90% Humidity 

 

.Storage environment range   

: -40

°

C to +70

°

C, 10% to 90% Humidity 

 

.Mounting  

 

 

: Wall mounted and US or European gang box 

 .Weight 

   : 

0.464lbs 

(210gm) 

 

.Dimensions 

 

 

: 4.17” x 3.40” x 1.22” 

 .Color 

   : 

Dark 

pearl 

grey 

 .Material 

   : 

Polycarbonate 

 .Format 

   : 

26-bit 

Wiegand 

 

.Certification 

 

 

: UL-294 indoor and outdoor compliance, FCC Class A part 15 and CE 

 

 

Summary of Contents for SENSORPROX 100R/PIN120



























Reviews: