manualshive.com logo in svg

senseFly EBEE RTK, Extended User Manual

The senseFly EBEE RTK Extended User Manual is a comprehensive guide that provides in-depth instructions for operating and optimizing your EBEE RTK drone. Designed for easy access and understanding, this manual is available for free download from our website, allowing you to make the most of your product's capabilities.

Share
Download
background image

Troubleshooting

10.2

Take-off vetoes

After successfully completing pre-flight checks the status LED becomes a solid
green to indicate that the drone is ready for take-off. At this point the

eBee RTK

continues to monitor its sensors and battery level. If at any point the drone detects
a condition that prevents it from beginning the automatic take-off procedure it
displays a Take-off veto in

eMotion

and the status LED changes to a blue pulse.

Once the Take-off veto is cleared the status LED returns to a solid green colour to
indicate that the drone is ready for take-off.

Table 4 on the next page presents all the Take-off vetoes that may occur and pos-
sible actions to remove the veto. If a veto persists after performing the suggested
action, we recommend you report the problem by following the instructions in
section ‘Reporting a problem with your

eBee RTK

’ on page 181.

161

Summary of Contents for EBEE RTK































































































































































































Reviews:

No comments

Related manuals for EBEE RTK

Parrot Rolling Spider Quick Start Manual preview
Rolling Spider
Brand: Parrot Pages: 2
Parrot Bluegrass User Manual preview
Bluegrass
Brand: Parrot Pages: 300
Hyper 3D-280 Assembly Manual And User Manual preview
3D-280
Brand: Hyper Pages: 26
TRNDlabs SWIFT User Manual preview
SWIFT
Brand: TRNDlabs Pages: 29
Jamara Loony Frog 3D AHP+ Instruction preview
Loony Frog 3D AHP+
Brand: Jamara Pages: 12
Quadrone TUMBLER Instruction Manual preview
TUMBLER
Brand: Quadrone Pages: 8
Idea-fly apollo A1 Operator'S Manual preview
apollo A1
Brand: Idea-fly Pages: 27
IDFTECH Poseidon Pro V2 User Manual preview
Poseidon Pro V2
Brand: IDFTECH Pages: 28
AEE TORUK AP11 User Manual preview
TORUK AP11
Brand: AEE Pages: 29
World Tech Toys HORIZON SPY DRONE Instruction Manual preview
HORIZON SPY DRONE
Brand: World Tech Toys Pages: 8
DELAIR UX5 HP User Manual preview
UX5 HP
Brand: DELAIR Pages: 137
AGR A22 2021 Manual preview
A22 2021
Brand: AGR Pages: 104

Brands by name

Popular brands

Load more brands