senseFly EBEE RTK Extended User Manual Download Page 162

Page: 162 / 190

Maintenance, Repair and Troubleshooting

Table 4: Take-oﬀ vetos

eMotion

text

Description and User action

Drone not
horizontal (roll or
pitch)

The

eBee RTK

must be held horizontally with level

wings to initiate take-oﬀ.

User action:

Hold the drone horizontally.

Motor is blocked

Excessive current was detected from the motor.

User action:

Check that the propeller is mounted

correctly and that the motor is freely turning and try
the take-oﬀ procedure again.

Battery too low for
take-oﬀ

The drone requires a fully-charged battery for the
take-oﬀ procedure.

User action:

Change the battery.

Wings not
detected

The drone’s wings are not attached correctly or the
wing struts are damaged.

User action:

Ensure that the wings are fully inserted

into the main body and that the wing struts are
not damaged, as described in section ‘Preparing the

eBee RTK

for ﬂight’ on page 41.

USB cable
detected

The

eBee RTK

has detected a USB cable connected to

the drone’s autopilot.

User action:

Remove the USB cable before take-oﬀ.

RTK source not de-
ﬁned

You have chosen a ﬂight mode that requires RTK cor-
rection data, but none is available.

User action:

Check that your GNSS/RTK base station

is powered on and connected to the computer that
is running

eMotion

Check that you have selected the correct base station
connection type and parameters in

eMotion

Check that you have set up and, if necessary, logged
in to your VRS stream.

162

Summary of Contents for EBEE RTK






























































































































































































Search results

Summary of Contents for EBEE RTK

Reviews:

Related manuals for EBEE RTK

Brands by name

Popular brands

senseFly EBEE RTK, Extended User Manual

Search results

Summary of Contents for EBEE RTK

Reviews:

Related manuals for EBEE RTK

Brands by name

Popular brands