manualshive.com logo in svg

senseFly EBEE RTK, Extended User Manual, Page: 48 / 190

Share
Download
senseFly EBEE RTK Extended User Manual Download Page 48

Quick start guide

RTK

Step 6: Connect to

eMotion

Start by connecting the USB ground modem to your computer. Then launch

eMo-

tion

, which will display the Connection window. Select the

eBee RTK

connection

profile, choose the corresponding FTDI port and click ‘OK’.

Note:

Every

eBee RTK

is paired with the ground modem it is deliv-

ered with, and will only work with that particular modem. The name
of the FTDI port corresponding to the ground modem is labelled as
‘

eBee RTK

-SERIAL’, where SERIAL is the serial number of the drone it is

paired with.

When a connection is established

eMotion

will display a map and the Status Panel

indicating the current state of the drone. If the

eBee RTK

has not yet detected its

location the Status Panel will appear in the top right corner of the Map Area with
the text ‘GPS/GLONASS: Waiting for signals...’. During this time the status LED on
the drone will pulse blue.

Once your drone has set its position using GPS/GLONASS signals, an icon of the
drone will appear at its location on the map. If the drone’s location is not on the
map you can click the

button from the Toolbar to centre the map on the drone.

The drone’s status on

eMotion

will be displayed as ‘Idle, Ready to take-off’ and the

status LED will become solid green.

48

Summary of Contents for EBEE RTK































































































































































































Reviews:

No comments