manualshive.com logo in svg

senseFly EBEE RTK, Extended User Manual

The senseFly EBEE RTK Extended User Manual is a comprehensive guide that provides in-depth instructions for operating and optimizing your EBEE RTK drone. Designed for easy access and understanding, this manual is available for free download from our website, allowing you to make the most of your product's capabilities.

Share
Download
background image

Quick start guide

preflight checks failed

blue

pulse

status LED:

green

solid

status LED:

ready for startup

connect battery

red

blink

status LED:

disconnect battery

connect battery and

insert into

compartment

close battery

compartment

Startup

process:

Step 5: Install and connect the battery

Lay the

eBee RTK

horizontally on the ground outside in the vicinity of the take-

off location, with the top face up. To install the battery, begin by connecting the
power cables to the battery. Insert the connectors firmly to the end in order to
avoid undesired disconnection when in flight. Once connected, insert the battery
into its compartment and close the compartment lid.

Caution:

Take care to keep the propeller area clear, in case it sud-

denly starts spinning.

46

Summary of Contents for EBEE RTK































































































































































































Reviews:

No comments

Related manuals for EBEE RTK

C-Fly obtain User Manual preview
obtain
Brand: C-Fly Pages: 18
C-Fly DF805 Quick Start Manual preview
DF805
Brand: C-Fly Pages: 8
Radio Shack Vektor Drone Manual preview
Vektor Drone
Brand: Radio Shack Pages: 2
SYMA X600W Instructions For Use Manual preview
X600W
Brand: SYMA Pages: 16
ehang GHOSTDRONE 2.0 VR Quick Start Manual preview
GHOSTDRONE 2.0 VR
Brand: ehang Pages: 2
sky viper 01646 Flying Manual preview
01646
Brand: sky viper Pages: 4
Eachine NOVICE-II Manual preview
NOVICE-II
Brand: Eachine Pages: 4
ZERO-X stratus+ User Manual preview
stratus+
Brand: ZERO-X Pages: 42
Parrot ANAFI How To Maintain preview
ANAFI
Brand: Parrot Pages: 3
WLtoys V636 SKYLARK Instruction Manual preview
V636 SKYLARK
Brand: WLtoys Pages: 8
Skylift Drones X8 800 User Manual preview
X8 800
Brand: Skylift Drones Pages: 7
Air Hogs STAR WARS X-WING VS DEATH STAR Instruction Manual preview
STAR WARS X-WING VS DEATH STAR
Brand: Air Hogs Pages: 4

Brands by name

Popular brands

Load more brands