manualshive.com logo in svg

senseFly EBEE RTK, Extended User Manual

Share
Download
senseFly EBEE RTK Extended User Manual Download Page 41

Executing a flight

Caution:

The

eBee RTK

should not be launched if the wind speed ex-

ceeds 12 m/s (in other units: 43.2 km/h, 26.8 mph, 23.3 kts).

Caution:

The

eBee RTK

is not designed to fly in temperatures above

35

◦

C. Avoid exposing the drone to high temperature for prolonged

periods of time. In particular, leaving the drone exposed to the sun
or in a car should be avoided.

4.2

Preparing the

eBee RTK

for flight

The

eBee RTK

’s simple design means it can go from the box to being ready for flight

in minutes. We recommend that you perform the following 6 steps before every
flight to ensure that the platform is best prepared for flight.

Note:

Remove the red warning sticker from the motor before your

first flight.

Central body
bottom view

Central body

top view

Wing - detached

3

4

2

5

6

41

Summary of Contents for EBEE RTK































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands