manualshive.com logo in svg

senseFly EBEE RTK, Extended User Manual, Page: 160 / 190

Share
Download
senseFly EBEE RTK Extended User Manual Download Page 160

Maintenance, Repair and Troubleshooting

De-calibrated
INS or Attitude
malfunction

The orientation sensors were not calibrated correctly.

User action:

Be sure to place the drone on a flat

surface, reconnect the battery and do not move the
drone until pre-flight checks are complete. If the
problem persists, perform Check 2 in section ‘Full air-
frame and sensor inspection’ on page 151. If this
does not solve the problem contact your

eBee RTK

re-

seller.

Ground sensor
malfunction

There is an error with the drone’s ground sensor.

User action:

Ensure that the ground sensor on the

bottom of the drone is clear of debris and is not dam-
aged, then re-connect the battery. If the problem
persists, perform Check 4 in section ‘Full airframe and
sensor inspection’ on page 151. If this does not solve
the problem contact your

eBee RTK

reseller.

Invalid flight
controller gains

There is an error with the firmware in the drone’s au-
topilot.

User action:

Re-connect the battery. If the problem

persists, contact your

eBee RTK

reseller.

160

Summary of Contents for EBEE RTK































































































































































































Reviews:

No comments