manualshive.com logo in svg

senseFly EBEE RTK, Extended User Manual

Share
Download
senseFly EBEE RTK Extended User Manual Download Page 54

Quick start guide

tude transition behaviours and how to modify them.

4.4

Take-off

Once you’ve planned your mission and the

eBee RTK

status LED is solid green you

can launch it using the procedure on the following pages.

Caution:

Make sure to keep the propeller area free of all obstructions

at all times during the launch procedure.

no 

holdin

g z

on

e

d

an

ger z

o

ne

green

solid

status LED:

blue

pulse

status LED:

Not horizontal!

Step 1: Orient horizontally and against the wind

Orient yourself against the direction of the wind, and confirm that the take-off
direction in front of you is free of obstacles. Firmly grasp the drone with both
hands, one hand on the front of each wing as shown in the figure. Hold the drone
horizontally with the nose pointed against the wind and level wings.

54

Summary of Contents for EBEE RTK































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands