background image

 Digital 9000

 

| 71

Using the EM 9046

Assess the result of the walk test:

Interference due to extraneous RF signals and low antenna signals can
impede the evaluation of a transmitter’s RF signal. In this case, the window
displaying the recorded antenna signals is highlighted in light gray.

Reposition the antennas to minimize interference and to optimize the
reception of transmission signals.

Call up the “

RF level recorder

” menu item again and repeat the walk

test.

Extended menu “

Transmitter setup

Via the extended menu “

Transmitter setup

”, you can adjust the transmit-

ter settings and then synchronize them via infra-red. 

The menu items allow you to adjust settings over the entire value range of
the Digital 9000 transmitters. Please note, however, that the actual values
are determined by the hardware configuration of your transmitters
(frequency  range,  type  of  microphone  head  being  used  (SKM),  type  of
Sennheiser microphone or cable being used (SK), etc.). 

If you adjust settings that are not supported by the transmitters’ current
hardware configuration, the value actually adopted by the transmitter is
written back to the menu item of the extended menu “

Transmitter setup

”. 

If you transfer a frequency range that is not supported by your transmit-
ter, “

Sync Fail

” is displayed in the menu selection of the receiver’s display

panel.

Modifications made via the “

Transmitter setup

” menu item of the EM 9046

must be synchronized via infra-red.

Modifications made directly on the transmitters have direct effect on the
menu items of the extended menu “

Transmitter setup

” of the EM 9046.

For details on the adjustment ranges of your transmitters, refer to the
description of the transmitters’ operating menu.

Start fullscan

MHz

CH 1

790

0:00

0:30

1:00

1:30

2:00

min

000

Showing RF level or channel 1

RF IN A
RF IN B
no signal

cmd

A
B

rf level rec

Low antenna signals: RF signal cannot be 
evaluated, the window is highlighted in gray

Diversity evaluation

Antenna signals

COMMAND button 
has been pressed

Summary of Contents for SKM 9000














































































































Reviews: