SENDER RAMPS PROGRESSION Series Manual Download Page 23

  

 

BOLTING TWO TABLETOP END PLATES TOGETHER

 

 
The images below show a Double Tabletop Drop Off. This is the perfect length of surface for coaching Drops. You may wish to 
place a small ramp at the end of the drop to reduce the Drop Height. 
 

  

 

 

COMPACT MODE and SUPER COMPACT MODE 

 
You can easily store you Tabletop with all the Leg Sets attached and folded. It takes a few minutes extra to remove the Tabletop 
Joining Blocks and Legs and Half the Size. 
 

  

 

 
STORING YOUR RAMP – KEY POINTS TO REMEMBER 

 

Your ramp should be stored in a dry location. Shipping Containers are terrible for humid, warm and cold conditions that are 
perfect for growing mould and mildew. Birch Plywood (and other sheet materials) are prone to these growths if it is not treated. 
Your ramp CAN BE used outside in the rain and in wet grass but if you would like your ramp to last a lifetime bring it inside after 
use. We strongly recommend treating your ramp with a preservative. Please see below. 
 
Never leave your ramp in the transport bag if it has been used in wet grass or in the rain. 

 

SENDER TRANSPORT BAG 
 

Our Transport bags are manufactured in the UK. They are strong but not indestructible. The webbing straps are double welded 
but you must avoid picking the ramp up with one strap! Use the Lifting Loop and a strap at the same time to mount the ramp on 
your bag with increase the life span of the bag. 

Summary of Contents for PROGRESSION Series

























Reviews: