Security Command 670, User Manual, Page: 9 / 32

7
Area Assignment: Area Assignment: Area Assignment: Area Assignment: Area Assignment: The Area Arming system can contain one or two individual
areas. Your burglary alarm system has been divided into ___ separate areas. The
specific area names should be listed below for easy reference.
Area Name
_______-_______________________
_______-_______________________
Arming or Disarming: Arming or Disarming:
Arming or Disarming: Arming or Disarming: Arming or Disarming: The first choice to be made is if you wish to arm or disarm.
Arming or disarming may be done for all areas at one time or each area may be
controlled individually. If a code number is required you will only be allowed to
control the areas which are assigned to your code number.
Arming: Arming: Arming: Arming: Arming: When arming is selected a code number may be required. This is
optional. The option is programmed during system installation. If a code number is
required you will only be able to arm the areas which are assigned to your code
number. If no code number is required you will be able to arm all areas.
All Or Selective Arming: All Or Selective Arming:
All Or Selective Arming: All Or Selective Arming:
All Or Selective Arming: After entering your code number you will be asked if
you wish to arm all of the areas to which you have access or only a selected area.
If you choose to arm all areas the system will begin checking to see that all loops
are in a good condition. If you choose to arm a selective area the SECURITY
SECURITY SECURITY SECURITY SECURITY
COMMAND COMMAND
COMMAND COMMAND
COMMAND will allow you to choose the individual area you want to arm before
beginning the loop check.
Bypassing: Bypassing: Bypassing: Bypassing: Bypassing: After you have made your arming selection the SECURITY SECURITY SECURITY SECURITY SECURITY
COMMAND COMMAND COMMAND COMMAND COMMAND will display any loops which have been bypassed prior to arming . This
is for your information only and they may not be reset during arming. They will
remain bypassed until disarmed or reset. Any 24 hour loops which are in a bad
condition will also be displayed. The system will then check to see that all doors
and windows which will be armed are closed and that any motion detectors, etc.,
are set properly.
SYSTEM ARMING AND DISARMING FOR AN AREA SYSTEM
If no problems exist the areas you have selected will be armed. If a problem does
exist on one or more loops the SECURITY COMMAND
SECURITY COMMAND SECURITY COMMAND SECURITY COMMAND SECURITY COMMAND will display the problems
and allow you to bypass those loops. If the problems can be corrected by simply
closing a door or window you should not bypass. You should correct the problems
and repeat the arming procedure. If the loop or loops are in some way damaged
and cannot be corrected they may be bypassed. Bypassing a loop means it will be
ignored while the system is armed. A code number may be required to bypass. This
is optional and is programmed during system installation.
Armed Message: Armed Message:
Armed Message: Armed Message: Armed Message: After all loops are bypassed or corrected the areas you selected
will be armed. The SECURITY COMMAND
SECURITY COMMAND SECURITY COMMAND SECURITY COMMAND SECURITY COMMAND will display “ALL SYSTEM ON” if all
areas are armed. The display will read “SYSTEM ON” if all areas are not armed.
The display will then show you the exit delay. Any exit loops will not be armed until
the delay expires.
One Moment Message: One Moment Message: One Moment Message: One Moment Message: One Moment Message: Your system may be programmed to wait for the
transmission of the arming signal to the central station receiver before displaying
the Armed Message. This is to insure that your phone lines are working properly.
While the system is waiting for the transmission the display will read “ONE
MOMENT...”. If the test is okay the Armed Message will be displayed. If the test
fails the display will read “LOCAL ALARM ONLY” before displaying the Armed
Message. If this is a multiplex communicating system and the closing report can
only be accomplished via a digital backup, the display will read "DIGITAL ALARM
ONLY". This communication test is optional and is programmed during system
installation.
Arming Report: Arming Report: Arming Report: Arming Report: Arming Report: A report of the system arming or loops which were bypassed
can be transmitted to your central station. This is optional and is programmed
during system installation.