Security Command 670, User Manual, Page: 12 / 32

10
SYSTEM ARMING FOR ALL/PERIMETER SYSTEM
Area Assignment: Area Assignment: Area Assignment: Area Assignment: Area Assignment: Your burglary alarm system has been divided into two separate
areas. Interior loops like motion detectors, inside doors, etc., have been assigned
to the interior area. Perimeter loops like windows, outside doors, etc., have been
assigned to the perimeter area. The specific loop names and their area assignment
are listed below for easy reference.
Interior area Perimeter area
Loop Name Loop Name
___ _ _________________________ ____ ________________________
___ _ _________________________ ____ _______________________
___ _ _________________________ ____ ______________________
___ _ _________________________ ____ ______________________
___ _ _________________________ ____ ______________________
___ _ _________________________ ____ ______________________
___ _ _________________________ ____ ______________________
___ _ _________________________ ____ ______________________
___ _ _________________________ ____ ______________________
___ _ _________________________ ____ ______________________
All or Perimeter: All or Perimeter: All or Perimeter: All or Perimeter: All or Perimeter: When arming your system you may arm only the perimeter area
if you are remaining inside, or arm both areas if you are leaving. The use of a code
number for system arming is optional. This option is programmed during system
installation.
Bypassing: Bypassing: Bypassing: Bypassing: Bypassing: After you have made your arming selection and have entered your
code number, if required, the SECURITY COMMAND
SECURITY COMMAND SECURITY COMMAND SECURITY COMMAND SECURITY COMMAND will display any loops which
have been bypassed prior to arming. This is for your information only. They will
remain bypassed until disarmed or reset using the Bypass Loops menu option. Any
24 hour loops which are in a bad condition will also be displayed.
The system will then check to see that all doors and windows which will be armed
are closed and that any motion detectors, etc., are set properly. If no problems exist
the system will be armed. If a problem does exist on one or more loops the
SECURITY COMMAND SECURITY COMMAND SECURITY COMMAND SECURITY COMMAND SECURITY COMMAND will display the problems and allow you to bypass those
loops. If the problem can be corrected by simply closing a door or window you
should not bypass. You should correct the problems and repeat the arming
procedure. If the loop or loops are in some way damaged and cannot be corrected
they may be bypassed. Bypassing a loop means it will be ignored while the system
is armed. A code number may be required to bypass. This is optional and is
programmed during system installation.
Armed Message: Armed Message: Armed Message: Armed Message: Armed Message: After all loops are bypassed or corrected the system will be
armed. The SECURITY COMMAND SECURITY COMMAND
SECURITY COMMAND SECURITY COMMAND
SECURITY COMMAND will display the “SYSTEM ON” message if
only the perimeter is armed or “ALL SYSTEM ON” if both have been armed. The
display will then show you the exit delay. Any exit loops will not be armed until the
delay expires. All other non-exit loops are armed immediately.
One Moment Message: One Moment Message: One Moment Message: One Moment Message: One Moment Message: Your system may be programmed to wait for the
transmission of the arming signal to the central station receiver before displaying
the Armed Message. This is to ensure that your phone lines are working properly.
While the system is waiting for the transmission the display will read “ONE
MOMENT...”. If the test is okay the Armed Message will be displayed. If the test
fails the display will read “LOCAL ALARM ONLY” before displaying the Armed
Message. If this is a multiplex communicating system and the closing report can
only be accomplished via a digital backup, the display will read "DIGITAL ALARM
ONLY". This communication test is optional and is programmed during system
installation.
Instant:
Instant: Instant: Instant: Instant: If you wish to cancel all exit and entry times, causing all loops to be instant
loops, you should press the “INSTANT” key while the exit delay is being displayed.
This immediately arms all entry/exit loops and there will be no entry delay when the
system is disarmed.
Arming Reports: Arming Reports:
Arming Reports: Arming Reports: Arming Reports: A report of the system arming or loops which were bypassed
can be transmitted to your central station. This is optional and is programmed
during system installation.