Section 06
ENGINE MANAGEMENT (DI)
Subsection 03
(COMPONENT INSPECTION AND ADJUSTMENT)
SMR2002-030 _06_03A.FM
06-03-1
COMPONENT INSPECTION AND
ADJUSTMENT
0
GENERAL
Engine problems are not necessarily related to the
electronic fuel injection system.
It is important to ensure that the mechanical integ-
rity of the engine/propulsion system is present:
– good jet pump/drive system operation
– good engine compression and properly operat-
ing mechanical components, no leaks etc.
– fuel pump connection and fuel lines without leaks.
Check the chart in TROUBLESHOOTING section
to have an overview of problems and suggested
solutions.
When replacing a component, always check its
operation after installation.
FUEL SYSTEM
– Use the VCK (Vehicle Communication Kit) (P/N 529
035 844) to release the fuel pressure in the system.
Look in the
Activation
section of the software
B.U.D.S.
– Always disconnect battery properly prior to
working on the fuel system.
When the job is done, ensure that hoses from fuel
rail going to fuel pump are properly secured in their
support. Then, pressurize the fuel system. Per-
form the high pressure test as explained in this
section and pressurize the fuel tank and fuel lines
as explained in FUEL SYSTEM section.
Properly reconnect the battery.
WARNING
Air compressor hose may be hot. Use a rag
or gloves or let hose cool down.
WARNING
The fuel system of a fuel injection system holds
much more pressure than on a carbureted wa-
tercraft. Prior to disconnecting a hose or to re-
moving a component from the fuel system, fol-
low the recommendation described here. Pay
attention that some hoses may have more than
one clamp at their ends. Ensure to reinstall the
same quantity of clamps at assembly.
WARNING
Fuel lines remain under pressure at all times. Al-
ways proceed with care and use appropriate
safety equipment when working on pressurized
fuel system. Wear safety glasses and work in a
well ventilated area. Do not allow fuel to spill on
hot engine parts and/or on electrical connectors.
Proceed with care when removing/installing
high pressure test equipment or disconnecting
fuel line connections. Use the VCK (Vehicle Com-
munication Kit)
to release fuel pressure prior to
removing a hose. Cover the fuel line connection
with an absorbent shop rag. Slowly disconnect
the fuel hose to minimize spilling. Wipe off any
fuel spillage in the bilge. Fuel is flammable and
explosive under certain conditions. Always work
in a well ventilated area. Always disconnect bat-
tery prior to working on the fuel system. After
performing a pressure test, use the valve on the
fuel pressure gauge to release the pressure (
if so
equipped
).
WARNING
Ensure to verify fuel line connections for dam-
age and that NO fuel line is disconnected prior
to installing the safety lanyard on the DESS
post. Always perform the high pressure test if
any component has been removed. A pressure
test must be done before connecting the safety
lanyard. The fuel pump is started each time the
safety lanyard is installed and it builds pressure
very quickly.
www.SeaDooManuals.net
Summary of Contents for GTI 5558
