background image

P:\INSTALLATION INST\Access Control\INST-936.vsd     0106     Page 10

NORMAL SYSTEM OPERATION

When the system is first powered up (or when communication is broken between the Keypad 
and the Control Module), the PROGRAM button in the Control Module must be pressed to 
establish the encoded connection. This also puts the system into setup mode. To end, press 
* * to exit. Or, the system will automatically exit programming if no entries are made for 30 
seconds.

KEYPAD LED STATUS INDICATORS

A flashing green LED indicates that the door is unlocked (momentarily).
A solid green LED indicates that the door is unlocked (latched).
A solid red LED indicates that the door is locked.

Depending on how the System Options are configured, User Commands are used to operate 
Manual Latching. The User Commands are trailing digits entered after an authorized user
code. The ability to use these User Commands depends on authorizations assigned to each 
User (see pages 18-19).

As the Main Output activates, the green LED will flash for 5 seconds. While the green LED is 
flashing, enter one (or more) of the following User Commands:

0 #

to Latch the Door Closed (Main Relay, 2

nd

 Door or 3

rd

 Door)

1 #

to Latch the Door Open (Main Relay, 2

nd

 Door or 3

rd

 Door)

2 #

to Turn Output A OFF (2

nd

 Output as Aux.)

3 #

to Turn Output A ON (2

nd

 Output as Aux.)

4 #

to Turn Output B OFF (3

rd

 Output as Aux.)

5 # 

to Turn Output B ON (3

rd

 Output as Aux.)

TAMPER ALARM

An audible Tamper Alarm sounds when four incorrect code entries are made. After 30 
seconds, the unit returns to standby mode.

CONTROL MODULE LED STATUS INDICATORS

Mode 

Green 

Red

Normal Operation 

On 

Off

Lockup Mode 

On 

Flashing

Setup Mode 

Flashing

Off

Connection Problems 

Off 

On

Summary of Contents for EntryCheck 936

























Reviews: