Scotsman C0522SR-1 Technical Manual Download | Manualshive

Page: 1 / 128

background image

Introduction

This technical manual covers the Prodigy line, excluding the Eclipse remote low side models.
All models except Eclipse are shipped with an Installation and User's manual, which can be
referred to separately. General installation information is included in this manual.

September 2006 Page 1

Table of Contents

Model Number Description . . . . . . . . . page 2

Water . . . . . . . . . . . . . . . . . . . . page 3

General Installation - Air or Water Cooled . page 4

Water purge setting . . . . . . . . . . . . page 8

General Installation - Remote . . . . . . . page 9

Pre-Charged Tubing Coupling Connections page 17

Adjustments . . . . . . . . . . . . . . . . page 20

Prodigy Cuber System Information. . . . . page 21

Controller Information . . . . . . . . . . . page 22

How It Works - Air Cooled . . . . . . . . . page 24

How It Works - Water Cooled . . . . . . . page 25

How It Works - Remote. . . . . . . . . . . page 26

Electrical Sequence - Air or Water Cooled . page 27

Electrical Sequence - Remote Cooled . . . page 29

Remote Schematics . . . . . . . . . . . . page 31

Electrical Component Details . . . . . . . page 32

Refrigeration . . . . . . . . . . . . . . . . page 35

Water System . . . . . . . . . . . . . . . page 36

Control Operation . . . . . . . . . . . . . page 37

Control Safeties . . . . . . . . . . . . . . page 38

Restarts. . . . . . . . . . . . . . . . . . . page 39

Control Button Use (from standby) . . . . . page 40

Control Button Use - continued . . . . . . page 41

Diagnostics – Air Cooled . . . . . . . . . . page 42

Low Ice Making Capacity - Air Cooled . . . page 45

Makes Excessive Noise - Air Cooled. . . . page 46

Diagnostics - Water Cooled . . . . . . . . page 47

Low ice Making Capacity - Water Cooled . page 50

Makes Excessive Noise - Water Cooled . . page 51

Diagnostics - Remote Air Cooled . . . . . page 52

Low Ice Making Capacity - Remote . . . . page 55

Makes Excessive Noise - Remote . . . . . page 56

Test Procedures - Sensors . . . . . . . . . page 57

Ice Thickness Sensor . . . . . . . . . . . page 58

Water Level Sensor . . . . . . . . . . . . page 59

Temperature Sensors . . . . . . . . . . . page 60

Test Procedures - Loads . . . . . . . . . . page 61

Compressor Electrical Chart . . . . . . . . page 62

Test Procedures - Loads . . . . . . . . . . page 63

Technical Information . . . . . . . . . . . page 71

Heat Load & Condenser Water GPM . . . page 72

Controller Differences . . . . . . . . . . . page 73

Thermistor Values . . . . . . . . . . . . . page 74

Performance Data . . . . . . . . . . . . . page 75

Performance Data - Remotes . . . . . . . page 85

Wiring Diagrams . . . . . . . . . . . . . . page 93

Repair Procedures . . . . . . . . . . . . . page 101

Refrigeration Removal and Replacement Procedures

. . . . . . . . . . . . . . . . . . . . . . . page 109

Optional add-on control information . . . . page 114

1
2
3
...
»

Summary of Contents for C0522SR-1

































































































































Reviews:

No comments

Related manuals for C0522SR-1

Saeco Poemia HD8325/08

Brand: Saeco Pages: 3

Brand: Rangemaster Pages: 48

Lavazza A MODO MIO

Brand: Saeco Pages: 2

Brand: Exido Pages: 1

PerfectCoffee MC05

Brand: Waeco Pages: 68

Incanto Rondo SUP021YO

Brand: Saeco Pages: 16

Brand: Ugolini Pages: 24

Brand: SwiftColor Pages: 16

Brand: inventum Pages: 40

Brand: Cooks Pages: 71

Brand: Sunbeam Pages: 92

Brand: Bunn Pages: 4

Brand: La Pavoni Pages: 8

Brand: Electrolux Pages: 4

Brand: Electrolux Pages: 2

Brand: Brewmatic Pages: 11

Brand: Klarstein Pages: 31

Brand: Waves Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands