SBG Navsight Apogee IMU Hardware Manual Download Page 43 | Manualshive

Page: 43 / 74

background image

Navsight Solution

– Hardware Manual

NAVSIGHTHM.1.3

5.8.3.3. Electrical specifications

This port shares the same electrical interface as the PORT B and C. See Electrical specifications.

5.8.4. PORT E interface

PORT E can be used for all common inputs and outputs functions. In addition to that the PORT E is the
dedicated interface for Odometer (DMI) connection.

A ded12V power supply is available on PORT E connector for easy connection with most precision
odometers.

5.8.4.1. Connector specifications (rugged)

The PORT E connector uses an 8 ways female ODU connector (ref G81F1C-P08LFG00000). Other
manufacturers such as Fischer provide compatible plugs (Fischer Core Series). The connector mates with
plug ref S31F1C-P08MFG0-5500.

Connector's pin out is the following:

Pin #

Name

Description

SHIELD

SHIELD

Connected to the mechanical ground

1

NC

Not internally connected

2

SGND

PORT E Signal ground

3

TX+

RS-422 Tx+

4

TX- / TX

RS-422 Tx- / RS-232 Tx

5

RX+ / RX / ODO A RS-422 Rx+ / RS-232 Rx / ODO A input

6

RX-

RS-422 Rx-

7

SYNC IN E / ODO B Synchronization input / ODO B input

8

+12V

+12V power supply output – may be used for odometer power

43/74

Figure 5.16: External plug

Figure 5.15: Receptacle front panel view

«
...
41
42
43
44
45
...
»

Summary of Contents for Navsight Apogee IMU











































































Reviews:

No comments

Related manuals for Navsight Apogee IMU

Brand: ESX Pages: 12

Brand: Metra Electronics Pages: 12

Mobile Video VOD128

Brand: Audiovox Pages: 30

Brand: Phonocar Pages: 28

SUNE10 PLUS-20ALPHARD/20 LM300h

Brand: Sune Technology Pages: 9

Brand: Audiovox Pages: 12

Brand: Audiovox Pages: 15

Brand: Audiovox Pages: 18

VOD8521 - DVD Player / LCD Monitor

Brand: Audiovox Pages: 11

Brand: Audiovox Pages: 24

VOD850 - Car - Overhead LCD Monitor

Brand: Audiovox Pages: 24

VOD916 - DVD Player With LCD Monitor

Brand: Audiovox Pages: 31

Brand: Audiovox Pages: 36

Brand: Audiovox Pages: 31

Brand: Audiovox Pages: 33

VOD85 - DVD Player With LCD Monitor

Brand: Audiovox Pages: 35

Brand: Pyle Pages: 31

Brand: RCA Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands