SBG Navsight Apogee IMU Hardware Manual Download Page 6

Page: 6 / 74

Navsight Solution

– Hardware Manual

NAVSIGHTHM.1.3

7.8.1. GNSS antennas...................................................................................................................................................................... 62
7.8.2. TNC Cables............................................................................................................................................................................. 62

8. Appendix B: Sub-systems mechanical outlines............................................................................................. 63

8.1. Ekinox IMU – Surface enclosure.............................................................................................................. 63

8.2. Ekinox IMU – Subsea enclosure............................................................................................................. 65

8.2.1. Top and bottom views........................................................................................................................................................... 65
8.2.2. Front view............................................................................................................................................................................. 65

8.3. Apogee IMU – Surface enclosure........................................................................................................... 66

8.4. Apogee IMU – Subsea enclosure............................................................................................................ 68

8.4.1. Top and bottom views.......................................................................................................................................................... 68
8.4.2. Front view............................................................................................................................................................................. 68

8.5. Horizon IMU............................................................................................................................................ 69

8.6. Processing unit – Rugged enclosure....................................................................................................... 71

8.7. Processing unit – Rack enclosure............................................................................................................ 73

9. Appendix C: Products labels............................................................................................................................ 74

6/74

Summary of Contents for Navsight Apogee IMU











































































Search results

Summary of Contents for Navsight Apogee IMU

Reviews:

SBG Navsight Apogee IMU, Hardware Manual, Page: 6 / 74

Search results

Summary of Contents for Navsight Apogee IMU

Reviews: