SBG Navsight Apogee IMU Hardware Manual Download Page 60

Page: 60 / 74

Navsight Solution

– Hardware Manual

NAVSIGHTHM.1.3

7.7.5. CA-NAVS-COM-2M

This open ended cable connects on any serial port or CAN bus plug of the
rugged processing unit. It has the following characteristics:

●

1 x ODU Mini-Snap F Series S31F1C-P08MFG0-5500 plug

●

1x open end

●

IP-68 rating

●

2m long

Pin on ODU plug

Signal on serial ports Signal on CAN port

Color

SYNC_OUT/NC

GREY

GND

BLACK

TX+

CAN H

WHITE

TX / TX-

GND

BLUE

RX / RX+

CAN L

YELLOW

RX-

ORANGE

SYNC_IN

RED

+12V out

GREEN

7.7.6. CA-NAVS-COM-DB-0.3M

This cable is a general purpose communication cable, that can be connected
on each serial port available in the rugged processing unit, as well as on the
CAN bus connector. General characteristics are the following

●

1 x ODU Mini-Snap F Series S31F1C-P08MFG0-5500 plug

●

1x Male DB-9 plug

●

IP-68 rating

●

30cm long

Cable wiring depends on the port on which user will connect the cable and is as follows

Pin on DB-9 plug

PORT A

PORT B/C/D/E

CAN

SYNC IN A

SYNC IN

PORT A RX

PORT # RX / RX+

CAN L

PORT A TX

PORT # TX / TX-

SGND

SYNC OUT A

SGND

RX-

TX+

CAN H

Note: This cable is included in the rugged processing unit package (3x units). It can also be ordered

separately.

60/74

Figure 7.11 : DB-9 cable adapter

Figure 7.10 : Open ended COM

cable

Summary of Contents for Navsight Apogee IMU











































































Search results

Summary of Contents for Navsight Apogee IMU

Reviews:

Related manuals for Navsight Apogee IMU

Brands by name

Popular brands

SBG Navsight Apogee IMU, Hardware Manual

Search results

Summary of Contents for Navsight Apogee IMU

Reviews:

Related manuals for Navsight Apogee IMU

Brands by name

Popular brands