SBC PCD1.Room Hardware Manual Download Page 42

Page: 42 / 95

Hardware Manual PCD1.M2110R1 │ Document 27-619 │ Version ENG 04 │ 2018-08-20

Saia-Burgess Controls AG

Program Download and Backup

CPU / Control Process Unit

3-19

3.11.2 Backup and Restore User Program

Backup with Saia PG5

Select a backup with

“Copy program to flash...”

Since the user program is already stored in the on-board flash memory, only

the RAM DB/text data from the on-board flash memory is backed up in the folder

PLC_SYS. This folder is not visible for the user. Access is not permitted.

Registers, flags, timer and counters are not saved in this manner.

During a restore, the text/DB data is copied back into the SRAM memory.

Backup to the INTFLASH file system

In order to be able to

use backup/restore with

internal flash, a PCD_

BACKUP folder must

be created.

RAM DB/text data is

stored in the internal

PCD_Backup folder.

This allows the backup

files to be accessed via

the FTP server and then

uploaded to a PC.

INTFLASH

PCD_BACKUP

*.sbak

Summary of Contents for PCD1.Room
































































































Search results

Summary of Contents for PCD1.Room

Reviews:

Related manuals for PCD1.Room

Brands by name

Popular brands

SBC PCD1.Room, Hardware Manual

Search results

Summary of Contents for PCD1.Room

Reviews:

Related manuals for PCD1.Room

Brands by name

Popular brands