SBC PCD1.Room Hardware Manual Download Page 15

Page: 15 / 95

Hardware Manual PCD1.M2110R1 │ Document 27-619 │ Version ENG 04 │ 2018-08-20

Saia-Burgess Controls AG

Installation

Orientation

2-9

2.2.6

Mounting a flat surface

Mounting on a flat surface is an additional variant using four screws. In the

following photograph, the two upper holes are used for fastening the housing and

the two lower holes serve as guides.

The following mounting instructions assume that the PCD is to be mounted

on a wall in front of the person performing the installation.

Two holes in the base plate for fastening

the controller..

Two holes in the base plate for two

additional guide screws.

Screw mounting:

The two lower screws must be tighten up to almost the thickness of the base plate.

This allows a correct mounting of the PCD.

155

106

Ø 4,9

Ø 8

118

These screws cannot be tighten, they are

covered by the print (see picture above).

Summary of Contents for PCD1.Room
































































































Search results

Summary of Contents for PCD1.Room

Reviews:

Related manuals for PCD1.Room

Brands by name

Popular brands

SBC PCD1.Room, Hardware Manual

Search results

Summary of Contents for PCD1.Room

Reviews:

Related manuals for PCD1.Room

Brands by name

Popular brands