SBC PCD1.Room Hardware Manual Download Page 3

Page: 3 / 95

Hardware Manual PCD1.M2110R1 │ Document 27-619 │ Version ENG 04 │ 2018-08-20

Saia-Burgess Controls AG

PCD1.M2110R1

Contents

0-2

Inputs and Outputs

4.1 On-board

............................................................................................... 4-1

4.1.1

Connection overview ............................................................................. 4-2

4.1.2

Digital Inputs (Terminal Block X1) ......................................................... 4-3

4.1.3

Digital Outputs (Terminal Block X0) ...................................................... 4-4

4.1.4

Digital Inputs and Outputs (Terminal Block X0) .................................... 4-5

4.1.5

PWM Output (Pulse width modulation) (Terminal Block X0) ................. 4-6

4.1.6

Interrupt Inputs (Terminal Block X1) ...................................................... 4-8

4.1.7

Analogue Inputs (Terminal Block X1) .................................................... 4-10

4.2

Plug-In I/O Module for slot A ................................................................. 4-13

4.2.1

Analogue outputs .................................................................................. 4-13

4.3

Plug-In I/O Modules for slot IO0 ............................................................ 4-17

4.4

Analogue Inputs and Outputs (Slot IO1) ............................................... 4-18

4.4.1

Analogue Inputs .................................................................................... 4-19

4.4.2

Analogue Outputs ................................................................................. 4-20

4.5

RIO (Remote I/O) .................................................................................. 4-21

System Cables and Adapters

Communications Interfaces for PCD1.M2_

6.1 On-board

............................................................................................... 6-2

6.1.1

USB Port (Programming Interface) ....................................................... 6-2

6.1.2

Port #9 Ethernet .................................................................................... 6-3

6.1.3

Port #0 (RS-485, not electrically isolated) ............................................. 6-4

6.1.4

Port #1 (Slot A) ...................................................................................... 6-5

6.1.4.1

PCD7.F110S Serial Interface Module RS-485/RS-422 ......................... 6-7

6.1.4.2

PCD7.F121S Serial Interface Module RS-232 ...................................... 6-8

6.1.4.3

PCD7.F150S Serial Interface Module RS-485 ...................................... 6-9

6.1.4.4

PCD7.F180S Serial Interface Module Belimo MP-Bus ........................ 6-10

6.2

Serial Interface to I/O Slot ..................................................................... 6-11

6.2.1

General Comments about the Plug-In Module PCD2.F2xxx ................. 6-11

6.2.2

Communications Port with PCD2.F2xxx Modules ................................. 6-12

6.3

Modem Communication ........................................................................ 6-13

Configuration

7.1 Requirements

........................................................................................ 7-1

7.2

General Information .............................................................................. 7-1

7.3

Running the Saia PG5

Device Configurator

........................................ 7-2

7.3.1 Help

....................................................................................................... 7-3

7.3.2

Media Mapping for Digital Inputs On-Board ......................................... 7-4

7.3.3

Media Mapping for Digital Outputs On-Board ....................................... 7-4

7.4

Special Functions .................................................................................. 7-5

7.4.1

Digital inputs onboard ........................................................................... 7-5

7.4.2

Analogue inputs onboard ...................................................................... 7-6

7.5

Analog inputs / outputs on PCD2.W525 slot IO1 .................................. 7-8

8 Maintenance

8.1

General Information .............................................................................. 8-1

8.2

Battery Replacement for the PCD1.M2_ .............................................. 8-1

Summary of Contents for PCD1.Room
































































































Search results

Summary of Contents for PCD1.Room

Reviews:

Related manuals for PCD1.Room

Brands by name

Popular brands

SBC PCD1.Room, Hardware Manual

Search results

Summary of Contents for PCD1.Room

Reviews:

Related manuals for PCD1.Room

Brands by name

Popular brands