SBC PCD1.Room Hardware Manual Download Page 90

Page: 90 / 95

Hardware Manual PCD1.M2110R1 │ Document 27-619 │ Version ENG 04 │ 2018-08-20

Saia-Burgess Controls AG

Icons

Annex

A-1

A Annex

A.1 Icons

In manuals, this symbol refers the reader to further information in this manual or other

manuals or technical information documents. As a rule there is no direct link to such

documents.

This symbol warns the reader of the risk to components from electrostatic discharges

caused by touch.
Recommendation: Before coming into contact with electrical components, you should

at least touch the system’s negative pole (cabinet of PGU connector). However, it

is better to use a grounding wrist strap with its cable permanently attached to the

system’s negative pole.
This sign accompanies instructions that must always be followed.

Explanations beside this sign are valid only for the Saia PCD

Classic series.

Explanations beside this sign are valid only for the Saia PCD

xx7 series.

Summary of Contents for PCD1.Room
































































































Search results

Summary of Contents for PCD1.Room

Reviews:

Related manuals for PCD1.Room

Brands by name

Popular brands

SBC PCD1.Room, Hardware Manual

Search results

Summary of Contents for PCD1.Room

Reviews:

Related manuals for PCD1.Room

Brands by name

Popular brands