manualshive.com logo in svg

Savaria omega, Installation Manual

Share
Download
Savaria omega Installation Manual Download Page 24

Page 24 

OMEGA IPL Installation Guide

Part No. 000823, 06-m02-2012

Step 15

Install call stations

Install the call stations.

Procedure

1

Mount the call stations starting with the lowest landing. 
An example of a call station is shown below.

2

When mounting the call station, be sure to allow 
enough clearance for the carriage at the landings.

3

Mount the call station at a height of one meter (39 
inches) from the floor to the center of the call station.

4

If mounting the call station on a post instead of 
attaching it to the wall, ensure the post is plumb before 
mounting.

5

Wire the call stations according to the Electrical 
Schematics shipped with the lift.

Figure 64

 

Call station (for automatic platform)

Step 16

Route and connect electrical wiring

Route and connect all electrical wiring.

Procedure

1

Connect all electrical wiring in accordance with the 
Electrical Schematics provided with the lift.

2

Set up a ground connection (if required).

3

Choose the most effective method of wiring for your 
installation; no two systems are the same.

In general, the following electrical connections are 

required:

• 1 cable for upper hall call landing station
• 1 cable for lower hall call landing station
• 1 cable for each intermediate hall call landing station
• 1 cable for lower normal limit switch
• 1 cable for each intermediate normal limit switch
• 1 cable for lower final limit switch and overspeed 

switch

• 1 cable for upper normal limit switch and upper final 

limit switch

• 1 cable for motor connections
• 1 cable for connection of the brush contact

Summary of Contents for omega



































Reviews:

No comments

Brands by name

Popular brands

Load more brands