manualshive.com logo in svg

Savaria omega, Installation Manual

Share
Download
Savaria omega Installation Manual Download Page 19

        Page 19

Part No. 000823,  06-m02-2012 

OMEGA IPL Installation Guide

f. Be sure to check the tension of the rope around the 

drive wheel at the top of the stairway.

g. When you achieve the right tension, clamp the rope 

in the clamping system. Tighten the metal clamp 
around the bottom of the white plastic parts, 
remove the tensioning tool, and secure the rope 
with a rope clamp as shown below. DO NOT cut off 
the rest of the support rope.

Figure 47

 

Clamp rope in clamping system

4

Install the plastic tubing over the rest of the support 
rope and turn it into a circle as shown below. Secure 
with cable ties as required. Ensure it is fastened securely 
so it won’t interfere when the unit is running on the rail.

Figure 48

 

Plastic on rope

5

Connect the carriage power wires to the rope and 
sliding contact connections. Connect the black wire to 
the rope clamp and the red wire to the sliding contact 
between the rope levers in the tube as shown below. 
The red wire assembly is for the tube (ground).

Figure 49

 

Connect wires to rope and slider

Connect
RED wire

Connect
BLACK wire

Summary of Contents for omega



































Reviews:

No comments

Brands by name

Popular brands

Load more brands