manualshive.com logo in svg

Savaria omega, Installation Manual

Share
Download
Savaria omega Installation Manual Download Page 16

Page 16 

OMEGA IPL Installation Guide

Part No. 000823, 06-m02-2012

4

Underneath the platform, connect the fork (shown 
below) at the middle of the platform to the carriage 
using the hardware provided.

Figure 36

 

Connect platform fork to carriage

Platform

Carriage

Fork

5

Connect the arm mechanism swivel link from the 
carriage to the bottom hole of the platform hinge (at 
both sides of the platform) as shown below.

6

Adjust the screws as required so the platform is level.

Figure 37

 

Connect arm swivel link 

Platform
hinge

Arm swivel link

7

Connect the seat mechanism swivel link from the seat 
to the middle hole of the platform hinge (at the right 
side only). 

8

Adjust the link as required so the seat is level.

Figure 38

 

Connect seat swivel link 

These 2 parts
need to move
 freely to allow
the seat to fold
and unfold 

9

Connect the platform cable from the platform to the 
right side of the carriage as shown below.

Figure 39

 

Connect platform cable

Summary of Contents for omega



































Reviews:

No comments

Brands by name

Popular brands

Load more brands