manualshive.com logo in svg

Satec PM130E, Installation And Operation Manual

Share
Download
Satec PM130E Installation And Operation Manual Download Page 47

 

Chapter 5  Data Display 

 

40 

Frequent failures may be the result of excessive electrical noise in 
the region of the instrument. If the instrument continuously resets 
itself, contact your local distributor. 

Table 5-3  Self-Test Diagnostic Codes 

Code Meaning 

1 ROM 

error 

2 RAM 

error 

3 

Watch dog timer reset 

4 Sampling 

failure 

5 

Out of control trap 

7 Timing 

failure 

8 

Normal power up 

9 

External reset (warm restart) 

 

NOTE 

The

 PM130

 provides a self-check alarm register accessible through 

communications that indicates possible problems with instrument 
hardware or setup configuration. The hardware problems are indicated 
by the appropriate bits which are set whenever the instrument fails self-
test diagnostics or in the event of loss of power. The setup

 

problems are 

indicated by the dedicated bit which is set when either configuration 
register is corrupted. In this event, your instrument will use the default 
configuration. For more information on the self-check alarm register, refer 
to the communications reference guides provided with your instrument. 
  

Summary of Contents for PM130E
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands