manualshive.com logo in svg

Satec PM130E, Installation And Operation Manual

Share
Download
Satec PM130E Installation And Operation Manual Download Page 34

Chapter 4  Setup Menus 

27 

 

4.5  Relay Operation Control Menu 

                                                                       

This menu allows you to set the relay operation mode: non-failsafe 
or failsafe. Failsafe relay operation is the opposite of normal 
operation where relay contacts are closed when a relay is 
operated (activated), and are open when a relay is released (de-
activated). In failsafe mode, an alarm is activated by a non-
energized relay which will open in all cases when an alarm 
condition is present or an alarm setpoint is not operational either 
due to a loss of control power or due to corruption of the setpoint 
setup configuration. A failsafe relay is closed only if it is under 
setpoint control and no alarm conditions exist, or if it is manually 
operated via communications. 

To change the relay operation mode: 

  Press               to activate the lower window.  
  Use the up/down arrow keys to set the desired 

option. Select 

nor

 for normal (non-failsafe) relay 

operation, or select 

FSAFE

 for failsafe relay 

operation. 

  Press                to store your new setting or press           to 

leave your previous setting unchanged. 

To quit the setup menu: 

 From the middle window, press           or               . 

 

NOTES 

1.   You will not be able to change the relay operation mode if a relay has 

been allocated for pulsing. 

2.   When a failsafe relay is allocated for pulsing, it automatically reverts 

to normal operation.   

SELECT

 

CHG

rELo

 

 

ENTER

 

ENTER

 

rELo 

   nor

 

   rEL 

ESC 

ESC 

SELECT

ENTER

ENTER

 

Summary of Contents for PM130E
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands