background image

STARTING POINT (0 DEGREES) ANGLE
SETTING

1

Use the joystick lever (

j

 

l

 

d

 

c

) to turn the camera to

the angle desired to become “0” degrees.

2

In the MAIN MENU, move the cursor to STARTING POINT,
then use the joystick lever (

d

 or 

c

) to set the North

direction. (Ex: SET) Then press the ENTER button.

ON” will replace “SET”, and the direction of the camera will
become “0” degrees. To return to the previously established
home position, use the joystick lever (

d

 or 

c

) to turn the

setting to “OFF”. The camera will return to the home position.

Available settings:

OFF: Position marked by “FRONT” is 0 degrees.

ON: A special position that has been set is 0 degrees.

SET: Sets the designated surveillance position as 0

degrees.

Note:

Calibration of degrees is in clockwise direction. East is 90
degrees when north is 0 degrees.

The camera’s angle information is taken and sent through the
communications line for status purposes. (Sent through the
RS-232C line on the system controller.)

3

Use the joystick lever (

d

 or 

c

) to move the cursor to

END, then press the ENTER button.

To return to the normal screen.

       MAIN MENU
 LANGUAGE        SET  ‚
 PRESET POSITION SET  ‚
 CAMERA          SET  ‚
 AUTO MODE       PAN  ‚
 AUTO FLIP       OFF
 ALARM           OFF
 FREEZE          OFF
 REFRESH         OFF
 STARTING POINT  SET  ‚

 MENU            END

0 degrees
(OFF position)

ON

OFF

FRONT

0 degrees (New status purposes)

English

– 49 –

Summary of Contents for VCC-9400























































Reviews: