117
18. Installation of the water dispenser line
1) For automatic operation of the ice maker, water pressure of 1.4~4.5Kgf/ is required.(It is
acceptable if the disposable paper cup(177cc) can be filled up with water within a second.)
2) The water tube can be used by cutting to the desired length. Make sure that the tube is not
bent.
3) Make the maximum length of the water tube to be 12m, if possible. If the length is over 12m,
it will cause a problem to supply water because of decrease of water pressure.
4) Locate the water tube at the area without heat.
5) The purifier is just for filtration. It will not work as sterilizer of microorganisms.
6) If the refrigerator is installed in the area with low water pressure(below 1.4 Kgf/ ),
additionally purchased booster pump may be installed in order to compensate the shortage
of pressure.
7) The life cycle of purifier depends upon the condition of the usage, but we recommend that
you change it every 6 months. So we recommend to install it at an eccess place for changing.
8) To supply water to the storage tank inside the refrigerator, press the cold water button for
about 2 or 3 minutes and make cold water drop from the cold water outlet.
9) In order to avid possible leakage, seal every joined area using sealing tape.
10) The water tube should be commected to the cold tap water.
Check the components
1. Connect couplers and valve to the
water pipe.
1) Close the main water valve.
2) Connect the coupler ÒAÓ to the tap water
valve.
3) Connect the coupler ÒAÓ and ÒBÓ to the
water pipe.
4) Every joint should be taped with sealing
tape.(see the picture)
5) If there is only one water pipe, connect
coupler ÒAÓ
If the coupler A and B doesnÕt fit to
the existing water pipe, consult the
closest authorized service dealer and
purchase the right couplers for the
proper installation.
2. Connect the water tube to water tube valve
1) Insert the nut into the water
tube
2) Insert the water tube into the
water tube valve as shown in
the picture on the right side.
3) Tighten the nut by turning it.
The water tube should be connected
to the cold water pipe. If it is connected
to the hol water pipe, it may cause
some problems in the Functioning of
the purcher.
PRECATUTION!
6. Fix the purifier.
1) Fix the purifier as shown int he
picture on the right.
3. Select the purifier location for installation
1) Cut the water tube, attached to
the purifier, to the proper length
after measuring the distance from
the location of the purifier to the
water tube valve.
2) If you want to reassemble the
water inlet side and outlet side of
the purifier during the installation
of the purifier, see the reference
picture.
4. Remove the residuals inside the purifies.
1) Open the main water valve to
check whether water is running
through the water tube from the
water inlet side of the purifier.
2) If water doesnÕt come out through
the tube, turn the water tube
valve.
3) Leave the faucet open until clean
water is running out.
4) It is no problem with the residuals
because it might be left while
manufactruing the filter.
5. Fix the purifier lock station.
1) Hold the purifier lock station
against the lock hole of right-
lower side in the back of the
refrigerator and fix it tightly
using screw.
7. Connect the water tube to the refrigerator.
1) Remove the back cover of
the refrigerator.
2) Connect the water tube to
the valve through the hole in
the back cover as shown in
the picture.(The connector is
lockated at right side of the
machine room in the back of
the refrigerator.)
3) When connected, check
whether there is any leakage.
On leakage, reassemble them.
8. Put the water tube in order
1) Using the clip ÒAÓ and ÒBÓ fix
the water tube to the wall.
2) When the water tube is put in
order, make sure there are any
forced bending and pushing
against the water tube.
CLIP A
CLIP B
WATER TUBE
9. Complete the installation of the water dispenser line
1) Turn on the refrigerator and press
the left side lever until water is
coming out through the water
tube.(approximately 2~3minute)
(Press it until the initial air outing
phenomenon disappear.)
2) At this time, check any possible
leakage on the joints of the water
tube. After putting the water
tube in order, move the refrigerator
to the desired location. Once the
refrigerator is located, do not move
the refrigerator as possible.
