Samsung SCX-4701ND Service Manual Download Page 106

Page: 106 / 127

4. Alignment and Troubleshooting

► Error Code

S6–3123

► Error message

Network Problem : IP Conflict

► Symptom

Network has some problem. (IP address conflicts with that of other system. / Communication error / There is no
response when checking the ping test.)

► Troubleshooting method

Change the machine’s IP address.

•

Execute the Samsung Easy Printer Manager program. (Device setting — Network — IP address). Change the
IP address.

•

In case of DHCP or Bootp, reboot the machine to receive a new IP address.

► Error Code

U1–2320

► Error message

Error #U1-2320 Turn off then on

► Symptom

The temperature control of fuser unit is abnormal. (Open Heat Error)

► Troubleshooting method

1) Turn the machine off. Re-install the fuser unit. Then turn the machine on. Is the error message is disappeared?

2) If the problem persists, turn the machine off and remove the fuser unit. Check if the fuser connector is connected

properly. Check if the input voltage is normal.

► Error Code

U1–2330

U1–2340

► Error message

Error #U1-2330 Turn off then on

Error #U1-2340 Turn off then on

► Symptom

The temperature control of fuser unit is abnormal. (Low Heat Error or Over Heat Error)

► Troubleshooting method

1) Turn the machine off. Re-install the fuser unit. Then turn the machine on. Is the error message is disappeared?

2) If the problem persists, turn the machine off and remove the fuser unit.

a) Check if the fuser connector is connected properly.

b) Check if the input voltage is normal.

c) Check if the thermistor is twisted or contaminated.

4-39

Summary of Contents for SCX-4701ND






























































































































Search results

Summary of Contents for SCX-4701ND

Reviews:

Related manuals for SCX-4701ND

Brands by name

Popular brands

Samsung SCX-4701ND, Service Manual

Search results

Summary of Contents for SCX-4701ND

Reviews:

Related manuals for SCX-4701ND

Brands by name

Popular brands