Samsung SCX-4701ND Service Manual Download Page 96

Page: 96 / 127

4. Alignment and Troubleshooting

► Error Code

A1–1110

► Error message

Error #A1-1110 Turn off then on

► Symptom

After working the main BLDC motor, the Ready signal has not occurred within 1 sec.

► Troubleshooting method

※

First, turn the machine off then on. If the error persists, refer to the following.

1) Check if the motor connector on the main board is connected properly. Reconnect it.

2) OPC coupler has overloaded. After removing the toner cartridge, rotate the OPC coupler. (Spec : 6 kgf.cm) If there

is any damage, the OPC coupler can’t rotate well. Replace the toner cartridge.

3) The main BLDC motor is defective.

- Unplug the connector from the motor carefully.

- Replace the main BLDC motor with new one.

4) If the problem persists, replace the main board.

4-29

Summary of Contents for SCX-4701ND






























































































































Search results

Summary of Contents for SCX-4701ND

Reviews:

Related manuals for SCX-4701ND

Brands by name

Popular brands

Samsung SCX-4701ND, Service Manual

Search results

Summary of Contents for SCX-4701ND

Reviews:

Related manuals for SCX-4701ND

Brands by name

Popular brands