Samsung SCX-4701ND Service Manual Download

Page: 108 / 127

4. Alignment and Troubleshooting

► Error Code

U3–3313

U3–3314

► Error message

Document jam. Remove jam

► Symptom

A document jam was detected in the ADF unit.

► Troubleshooting method

1) Remove the jammed paper from ADF unit. (Refer to 4.1.3.1)

2) If the error persists, turn the machine off then on.

3) If the document jam occurs continually, open the ADF cover-top. Check if the ADF pick up roller is contaminated

or worn out. Clean or replace it.

4) If the pick up roller is OK, check the followings.

a) Check if the ADF motor is working normally.

b) Check if the connector on the ADF joint board is connected correctly.

5) If the problem persists, replace the ADF unit.

► Error Code

U3–4110

► Error message

Door of scanner is open.

► Symptom

ADF or ADF top cover is opened.

► Troubleshooting method

1) Close the ADF unit.

2) Close the ADF top cover.

4-41

Summary of Contents for SCX-4701ND






























































































































Search results

Summary of Contents for SCX-4701ND

Reviews:

Related manuals for SCX-4701ND

Brands by name

Popular brands

Samsung SCX-4701ND, Service Manual

Search results

Summary of Contents for SCX-4701ND

Reviews:

Related manuals for SCX-4701ND

Brands by name

Popular brands