Samsung SCX-4701ND Service Manual Download Page 98

Page: 98 / 127

4. Alignment and Troubleshooting

► Error Code

C2–1410

► Error message

Install toner cartridge

► Symptom

The toner cartridge is not installed. / The machine can’t detect the toner cartridge.

► Troubleshooting method

1) Turn the machine off then on.

2) Remove the toner cartridge. Thoroughly roll the cartridge five or six times to distribute the toner evenly inside the

cartridge. And reinstall the toner cartridge.

3) Check if the CRUM contact area is contaminated. Clean it.

► Error Code

C2–1510

► Error message

Not Compatible Toner cartridge

► Symptom

Toner cartridge is not compatible.

► Troubleshooting method

1) Print the supply information report. Check information of the toner cartridge.

2) If the toner cartridge is not a Samsung genuine toner cartridge, replace with new one.

4-31

Summary of Contents for SCX-4701ND






























































































































Search results

Summary of Contents for SCX-4701ND

Reviews:

Related manuals for SCX-4701ND

Brands by name

Popular brands

Samsung SCX-4701ND, Service Manual

Search results

Summary of Contents for SCX-4701ND

Reviews:

Related manuals for SCX-4701ND

Brands by name

Popular brands