Samsung SCX-4701ND Service Manual Download

Page: 102 / 127

4. Alignment and Troubleshooting

► Error Code

M3–1110

► Error message

Paper Jam in exit area

► Symptom

A paper jam was detected in the exit area.

► Troubleshooting method

1) Open the rear cover. Remove the jammed paper. (Refer to 4.1.3 Jam removal)

2) Check if the Guide-Change Duplex of the rear cover is defective.

3) Check if the exit sensor and actuator is working normally.

► Error Code

M3–2130

► Error message

Output bin full Remove paper

► Symptom

The machine detected that the output tray has got full or the bin-full sensor is defective.

► Troubleshooting method

1) Remove the paper on the output tray.

(The maximum loading capacity is 150 sheets based on standard paper(80g/m2).)

2) Check if the Bin-full Sensor connector is connected properly. Reconnect it or replace the Bin-full sensor.

4-35

Summary of Contents for SCX-4701ND






























































































































Search results

Summary of Contents for SCX-4701ND

Reviews:

Related manuals for SCX-4701ND

Brands by name

Popular brands

Samsung SCX-4701ND, Service Manual

Search results

Summary of Contents for SCX-4701ND

Reviews:

Related manuals for SCX-4701ND

Brands by name

Popular brands