Samsung NQ25 User Manual Download Page 92

Page: 92 / 153

Customizing Your Computer 79

To switch display devices using shortcut key

You can switch display devices easily by pressing

<Fn>+<F5 / LCD/CRT>

shortcut key.
Provided that the CRT monitor is connected, the display order will be LCD >
CRT > LCD+CRT whenever the

<Fn>+<F5 / LCD/CRT>

key is pressed.

You cannot use the

<Fn>+<F5 / LCD/CRT>

shortcut key in the full screen

mode DOS prompt.

To change display devices easily

Right-click on the desktop, and select Graphics Options > Output To to change
the current display device easily.

To change the screen resolution and color quality

If the screen does not appear clearly, please try to change the screen
resolution and colour quality. In the figure of step 3, select a device, and
configure the color, screen area, and refresh rate.

Summary of Contents for NQ25


























































































































































Search results

Summary of Contents for NQ25

Reviews:

Related manuals for NQ25

Brands by name

Popular brands

Samsung NQ25, User Manual

Search results

Summary of Contents for NQ25

Reviews:

Related manuals for NQ25

Brands by name

Popular brands