Wireless network setup
_ 6
Troubleshooting
Printer Not Found
•
Your computer or machine may not turned on. Turn on your
computer or machine.
•
USB cable is not connected between your computer and machine.
Connect machine to your computer using USB cable.
•
The machine does not support wireless network. Check the machine
manual and prepare wireless network machine.
Connecting Failure - Not Found SSID
•
The machine is unable to search network name (SSID) which is
selected or entered name form you. Check the network name (SSID)
on your access point and retry to connect.
•
Your access point is not turned on. Turn on your access point.
Connecting Failure - Invalid Security
•
You configured security incorrectly. Check the configured security on
your access point and machine.
Connection Failure - General Connection Error
•
Your computer is not receiving a signal form your machine. Check
the USB cable and your machine power.
Connection Failure - Connected Wired Network
•
Your machine is connected wired network cable. Remove the wired
network cable form your machine.
PC Connecting Error
•
The configured network address is unable to connect between your
computer and machine.
-
For DHCP network environment
The print receives the IP address automatically (DHCP) when
computer is configured DHCP.
-
For Static network environment
The machine uses the static address when computer is
configured static address.
If computer is configured IP address as 192.168.1.100, Subnet
address as 255.255.255.0 and Gateway address as
192.168.1.1, input IP address as 192.168.1.101, Subnet address
as 255.255.255.0 and Gateway address as 192.168.1.1 on your
machine.
SETTING A WIRELESS NETWORK WITH
NETWORK CABLE
Your machine is a network compatible machine. To enable your machine to
work with your network you will need to perform some configuration
procedures.
Refer to your network administrator, or the person that set up your
wireless network, for information about your network configuration.
Preparing items
Ensure you have next items ready.
•
Access point
•
Networked computer
•
Printer Software CD-ROM that provided with your machine
•
Wireless network printer (your machine)
•
Network cable
Setting IP address
Firstly, you have to set up an IP address for network printing and
managements. In most cases a new IP address will be automatically
assigned by a DHCP (Dynamic Host Configuration Protocol) server located
on the network.
In a few situations the IP address must be set manually. This is called a
static IP and is often required in corporate Intranets for security reasons.
•
DHCP IP assignment
: Connect your machine to the network, and wait a
few minutes for the DHCP server to assign an IP address to the
machine. Then, print the
Network Configuration Report
as explained
above. If the report shows that the IP address has changed, the
assignment was successful. You will see the new IP address in the
report.
G
(See "How to print a network configuration report" on page 1.)
•
Static IP assignment
: Use SetIP program to change the IP address
from your computer.
In an office environment, we recommend that you contact a network
administrator to set this address for you.
IP setting using SetIP Program (Windows)
This program is for manually setting the network IP address of your
machine using its MAC address to communicate with the machine. A
MAC address is the hardware serial number of the network interface and
can be found in the
Network Configuration Report
.
For using SetIP program, disable the computer firewall before continuing
by performing the following:
1.
Open
Start
>
All programs
>
Control Panel
.
2.
Double click
Security Center
.
3.
Click
Windows Firewall
.
4.
Disable the firewall.
Installing the program
1.
Insert the Printer Software CD-ROM provided with your machine.
When the driver CD runs automatically, close that window.
2.
Start Windows Explorer and open the X drive. (X represents your
CD-ROM drive.)
3.
Double-click
Application
>
SetIP
.
4.
Double-click
Setup.exe
to install this program.
5.
Click
OK
. If necessary, select a language from the drop-down list.
6.
Follow the instructions in the window and complete the installation.
Starting the program
1.
Connect your machine to the network with a network cable.
2.
Turned on the machine.
3.
From the Windows
Start
menu, select
All Programs
>
Samsung
Printers
>
SetIP
>
SetIP
.
4.
Click on the
icon (third from left) in the SetIP window to open the
TCP/IP configuration window.
