Samson 3731-5 Mounting And Operating Instructions Download

Page: 47 / 112

EB 8387-5 EN

Mounting and start-up

Specified degree of protection is not
achieved due to insufficient sealing of the

terminal compartment.
Only operate the positioner with sealed

cable entries and locked cover.

Loss of the explosion protection due to dam-
age to the cover's thread and/or the con-

necting thread.

−

Do not open devices with flameproof en-

closures when the electrical power supply
is connected.

−

Observe explosion protection regulations.

5.11.2 Establishing communica

tion

The communication structure between the
controller or automation system or between
a computer or work station and the posi-
tioner(s) is implemented to conform with
EN 61158-2.

Refer to the Configuration Manual

KH 8387-5 for more details.

Accessories for electrical connection

See Table 6 on page 19.

WARNING

Note

Summary of Contents for 3731-5

















































































































Search results

Summary of Contents for 3731-5

Reviews:

Related manuals for 3731-5

Brands by name

Popular brands

Samson 3731-5, Mounting And Operating Instructions

Search results

Summary of Contents for 3731-5

Reviews:

Related manuals for 3731-5

Brands by name

Popular brands