- 17 -
10. OPERATION
VERY IMPORTANT!!
Only if the whole process indicated in the section regarding DEPRESSURISATION, described in section 9,
has been correctly carried out will the unit be ready to be started and used again.
The incorrect observance of this Depressurisation process could lead to malfunctions in the equipment and
deterioration of its components.
1.- Power switch (No. 8 Fig.1) starting the electric motor.
2.- With the engine running, Set the pressure regulator (No.
4, figure 1) to the minimum position (turn anticlockwise).
3.- Pull the spray gun trigger, holding it until gauge (No 7
Fig.1) indicate "0".
4.- Set the gun safety catch.
5.- Open the product return key (No 4 Fig.1).
6.- Bear the product cup (No.1 Fig.1).
7.- Turn the pressure regulator (No. 5 fig.1) clockwise until
the product flows smoothly through the product return Hose
(No. 3 fig.1).
8.- Close the product return key (No. 4 Fig.1).
9.- Turn the pressure regulator (No. 5 fig.1) to set the desired
application pressure, visible in the gauge (No. 7 Fig.1).
10.- Press the trigger on the gun, holding a metallic part of
the gun (the hand protector, for instance) in contact with the
metallic container.
Within a few seconds, product will flow from the head of the
gun which is not fitted with a cap. Maintain the flow of product
until this is even (no air) from the head.
11.- Set the gun safety catch.
12.- Install the air cap.
13.- Adjust the spray width:
13.1- Increase the pressure by means of the pressure
regulator (No.5, fig.1) until the product flowing from the gun
is fully atomised.
To avoid spraying too great a quantity of product, which may
lead to excessive mist and premature wear on the cap and
other parts of the equipment, always use the lowest pressure
setting possible to obtain the performance and thickness in
microns given by the manufacturer of the product.
13.2- Once the atomising pressure for the product has been
determined, if a greater quantity of product is required, it is
preferable to use a cap of greater diameter than to increase
the pressure during application.
13.3- To set the shape of the spray width, set the spray gun
safety catch, loosen the cap attachment bolt and turn to the
desired direction. Tighten the cap attachment bolt.
During application, the amount of product applied to areas
with difficult access, reduced space, etc. can be reduced by
decreasing the travel distance of the trigger when loosening
the grip of your fingers on it.
Adjust the distance between the air cap and the object to
be sprayed (10 / 20 cm.) depending on the same, the product
to be applied and the working conditions, in order to increase
transfer and obtain a reduction in the amount of mist
depending on the air cap used in each case.
11. STOPPING
11.1. Short stop
When stopping for a short period of time that does not pose
possible problems with catalysation or hardening of the
product inside the unit and accessories and apply the
procedure of Depressurisation (Section 9).
Set the motor switch (No.8, Fig.1) to the position “O” (off).
Disassemble the air cap and dip it in thinner.
11.2. Stopping when work is finished
11.2.1.- Apply the procedure of Depressurisation (Section
9).
11.2.2.- Disassemble the air cap and dip it in thinner
11.2.3.- Close the product return key. (No. 4 fig.1)
11.2.4.- Empty the contents of the tank through the gun, from
the original container containing the product from the start.
11.2.5.- Turn the pressure regulator (No.5, fig.1) to the
minimum setting (anticlockwise).
11.2.6.- Open the drain stopcock (No.4, fig.1) keeping a
container at hand in which to collect the product.
11.2.7.- Disconnect the motor switch (No.8, fig.1) turning it
to the setting “off”.
Now, the team is ready to proceed immediately to clean it.
