background image

 

INCANTO S-CLASS 

3. OPERATION 

Saeco International Group 

REV.1 FEB.2005 

Page 11/21 

 
 

 

Cleaning

 

 

 

  Empty dregs drawer

 

Storage capacity of 12 tablespoons (Reset - empty only 
when indicated and with machine on)

 

  Empty drip tray

 

After 12 servings

 

  Clean water tank.

 

As required.

 

  Clean coffee bean container.

 

As required.

 

  Clean the housing.

 

As required.

 

  Rinse brewing unit

 

1 x per week

 

  Clean brewing unit and lubricate 

Clean filter

 

1 x per month 

  Descale

 

According to indicator.

 

 
 

 

Descaling procedure

 

 

 

 

Action

 

Comments

 

Indication

 

 

 

 

Descale

 

 

Remove the Aqua Prima filter.

 

 

Descale

 

 

Fill tank with descaler solution.

 

Place an appropriately sized 
container under the HWS 
nozzle.

 

Descale

 

 

Press descaling button

 

 

Descale 
Open dial.

 

 

Open HWS valve

 

The pipes are rinsed with 
descaler at intervals. (Duration: 
approx. 45 min)

 

Machine is descaled.

 

 

Programme end

 

When water tank is empty

 

Descaling complete 

 

Close dial.

 

 

Close HWS valve

 

Descaling programme complete.

 

Rinse machine 
Fill water tank

 

 

Fill tank.

 

 

Rinse machine. 

 

Press button

 

 

Press descaling button

 

 

Rinse machine. 
Open dial.

 

 

Open HWS valve

 

 

Machine is rinsed

 

 

Programme end

 

When water tank is empty

 

Rinsing complete 

 

Close dial.

 

 

Close HWS valve

 

Rinse programme complete

 

Fill water tank.

 

 

Fill tank.

 

 

De-aerate

 

 

Open HWS valve

 

Until water is continuously 
discharged.

 

Hot water

 

 

Close HWS valve

 

 

Select product 
Ready for operation

 

 

Install Aqua Prima filter.

 

 

Select product 
Ready for operation

 

 

The descaling indicator turns off automatically after completion of the descaling process! 

 

Summary of Contents for RI9722/11

































































































































































































































Reviews: