Saeco RI9722/11 Service Manual Download Page 142

Page: 142 / 224

3. OPERATION

INCANTO

Page 16/16

REV.5 FEB.2005

Saeco International Group

Cannot dispense

Expresso, coffee and steam buttons
flash

- Overheating: Remove hot water until only expresso
and coffee buttons are lit.

Filter warning LED lights up

(MACHINE NOT LOCKED)

- Install Aqua Prima filter.

Reset:

Press steam button until filter warning LED

flashes

Warning LED lights up

- Fill water tank.
- Fill coffee beans container.
- Empty grinds container

Warning LED flashes

- Dregs drawer/drip tray not installed.
- Brewing unit not installed.
- Doors not closed.
- Grinder obstructed.
- Gears obstructed
- Contact an authorised service centre.

Summary of Contents for RI9722/11

































































































































































































































Search results

Summary of Contents for RI9722/11

Reviews:

Related manuals for RI9722/11

Brands by name

Popular brands

Saeco RI9722/11, Service Manual

Search results

Summary of Contents for RI9722/11

Reviews:

Related manuals for RI9722/11

Brands by name

Popular brands