rotork IQT Installation And Maintenance Instructions Manual Download Page 42

Page: 42 / 88

The available forms of remote control
are listed below:

Standard hardwired control
Analogue control-Option Folomatic
Network control including:

Option Pakscan
Option Modbus
Option Profibus

The setting for Remote Control Source
will depend on the type of remote
control required and the option
specified and fitted. Check actuator
circuit diagram for remote control form.

The setting of Remote Control Source
will be determined by the option that
has been fitted, if any.

[

Standard hardwired remote
control.

[bO]

Option Folomatic.

[OP]

Options Pakscan, Profibus,
Modbus, Foundation Fieldbus
or DeviceNet.

[OF]

All remote control disabled
(Actuator available for local
control only).

To change the remote source press the

key until the required setting is

displayed.

PRESS THE

KEY.

The displayed option will flash
indicating that it has been set.

Standard Hardwired

Remote Control

Remote Control Source

9.7

Remote Control Source

Summary of Contents for IQT

























































































Search results

Summary of Contents for IQT

Reviews:

Related manuals for IQT

Brands by name

Popular brands

rotork IQT, Installation And Maintenance Instructions Manual

Search results

Summary of Contents for IQT

Reviews:

Related manuals for IQT

Brands by name

Popular brands