rotork IQT Installation And Maintenance Instructions Manual Download Page 35

Page: 35 / 88

The default setting for ESD Override
Interlocks is

[OF]

. ESD action will not

override an active interlock applied to
the actuator.

If an applied ESD signal is required to
override active interlocks causing the
ESD action as set for A1, press the

key. The display will change to

]

PRESS THE

KEY.

The displayed option will flash
indicating that it has been set.

ESD Override Interlock – Off

The default setting for ESD Override
Local Stop is

[OF]

. ESD will not override

local stop when selected.

If an applied ESD signal is required to
override local stop causing the ESD
action as set for A1, press the

key. The display will change to

]

PRESS THE

KEY.

The displayed option will flash
indicating that it has been set.

ESD Override Local Stop – Off

The default setting for Local Actuator
Pushbutton control is self-maintained

]

If non-maintained actuator pushbutton
control is required (jogging, inching,
push to run), press the

key. The

display will change to

[OF]

PRESS THE

KEY.

The displayed option will flash
indicating that it has been set.

Self-Maintained Local Control

The default setting for 2-wire Remote
Control is Stayput

[SP]

. If a open and

closed remote control signal are applied
simultaneously the actuator will stayput
(stop if running). Refer to actuator
wiring diagram or publication E120E.

Use the

key to select the

required priority:

[OP]

Open

[SP]

Stay put

[CL]

PRESS THE

KEY.

The displayed option will flash
indicating that it has been set.

2-wire Control – Stayput Priority

ESD Override
Interlocks

ESD Override
Local Stop

Maintained
Local Control

2-wire Remote
Control

Summary of Contents for IQT

























































































Search results

Summary of Contents for IQT

Reviews:

Related manuals for IQT

Brands by name

Popular brands

rotork IQT, Installation And Maintenance Instructions Manual

Search results

Summary of Contents for IQT

Reviews:

Related manuals for IQT

Brands by name

Popular brands