rotork IQT Installation And Maintenance Instructions Manual Download Page 55

Page: 55 / 88

Setting instructions for actuators
including an optional DeviceNet DFU
module – check wiring diagram for
inclusion.

DeviceNet module set up screens can
be turned off to provide extra security.
The action of turning screens on or off
does not effect its operation.

Use the

key to turn on

DeviceNet set up screens.

DeviceNet Set-up Screens ON

PRESS THE

KEY.

The displayed option will flash
indicating that it has been set.

Press the

key to display the

DeviceNet set up displays.

The DeviceNet module must be
allocated a unique address.

Using the

keys display the

required address.

Address to be set within the range 01
to 3F Hexadecimal. See page 72 for
conversion. If an address value outside
this range is entered, the address set
will revert to 01 (for 00) or 3F (for value
above 3F).

PRESS THE

KEY.

The displayed option will flash
indicating that it has been set.

Press the

key to display

[Pb]

The DeviceNet module must be set to
the DeviceNet highway baudrate.

Using the

keys display the

required baudrate:

[01] 125 k baud

[03] 250 k baud

[06] 500 k baud

PRESS THE

KEY.

The displayed option will flash
indicating that it has been set.

Press the

key to display

[PF]

Option DeviceNet

9.11

DeviceNet Address

DeviceNet Baudrate

Summary of Contents for IQT

























































































Search results

Summary of Contents for IQT

Reviews:

Related manuals for IQT

Brands by name

Popular brands

rotork IQT, Installation And Maintenance Instructions Manual

Search results

Summary of Contents for IQT

Reviews:

Related manuals for IQT

Brands by name

Popular brands