rotork IQT Installation And Maintenance Instructions Manual Download Page 11 | Manualshive

Page: 11 / 88

background image

4.1 Bases F05 to F07

and FA05 to FA07

The base adaptor must be removed to
give access to the drive bush. Remove
the four capscrews and base adaptor as
shown in figure 4.

Fig. 4

Clear access to the drive bush is now
available as shown in figure 4. Using
the a 3mm allen key, unscrew the two
capscrews retaining the drive bush and
remove the drive bush from the
actuator.

Fig. 4.1

4.2 Bases F10 to F14

and FA10 to FA14

Removal of the drive bush does not
require the removal of the actuator
base. Using a 3mm allen key, unscrew
the two capscrews retaining the drive
bush.

Capscrews can be used to remove the
drive bush by screwing into the drive
bush as shown in figure 4.2.

Fig. 4.2

The range of IQT drive bushes is shown
in figure 4.3. Please refer to publication
E110E for maximum stem acceptance
details.

Fig. 4.3

4.3 Machining the Drive Bush

Once removed, the drive bush can be
machined to suit the valve stem. Ensure
machined position allows correct
orientation of actuator-to valve flange
and correct direction to close the valve.

4.4 Fitting the Drive Bush

Note: The drive bush can be fitted in
two possible positions, 180º apart. Fit
the drive bush into the centre column
ensuring that the stem orientation,
actuator position and direction of
operation are correct for valve
operation. Secure the drive bush with
the capscrews. For F05, FA05, F07 and
FA07 bases, refit the base adaptor and
secure with the four capscrews.

7

Preparing Drive Bush

4

«
...
9
10
11
12
13
...
»

Summary of Contents for IQT

























































































Reviews:

No comments

Related manuals for IQT

Brand: NCR Pages: 6

Brand: Samson Pages: 100

Brand: Danfoss Pages: 16

Brand: Radio Shack Pages: 3

Brand: Hardi Pages: 2

Brand: YASKAWA Pages: 64

Brand: V2 Pages: 3

Brand: Farfisa Pages: 20

Brand: Racal Instruments Pages: 64

Brand: Gate Motors Pages: 6

Brand: Harsco Industrial Pages: 57

Brand: Paradox Pages: 2

Brand: Paradox Pages: 44

Z3-DM8107-SDI-RPS

Brand: Z3 Technology Pages: 73

Brand: Z-Wave Pages: 14

Brand: Z-Wave.Me Pages: 4

Brand: K&K Pages: 10

MorphoAccess VP MD

Brand: Idemia Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands