input is taken on-air, off-air, or selected on the
preset bus of the program ME. A delay (preroll
or postroll) can be applied between the
transition and the starting of the custom control.
To Assign an On-Air Run CC
Select a custom control to be run when a video
source is taken on-air.
1.
Press
HOME
>
Setup
>
Installation
>
Source
Configuration
>
More
>
More
>
Attach CCs
>
On Air CC
.
2.
Use the
Source
knob to select the video
source that you want to assign a custom
control to.
3.
Use the
Cust Ctrl
knob to select the custom
control you want to run when the selected
source is taken on-air.
4.
Select whether the custom control always
runs when attached or only when Roll Clip
is active.
•
Always Active
— the custom control that
is attached to the source always runs.
•
Follow Roll Clip
— the custom control
that is attached to the source only runs
when Roll Clip is active.
5.
Use the
Preroll
knob to set the amount of
time the switcher will wait before
performing the transition. When you start
a transition, the switcher starts the custom
control and then waits the preroll time
before performing the transition.
To Assign an Off-Air Run CC
Select a custom control to be run when a video
source is taken off-air.
1.
Press
HOME
>
Setup
>
Installation
>
Source
Configuration
>
More
>
More
>
Attach CCs.
>
Off Air CC
.
2.
Use the
Source
knob to select the video
source that you want to assign a custom
control to.
3.
Use the
Cust Ctrl
knob to select the custom
control you want to run when the selected
source is taken off-air.
4.
Select whether the custom control always
runs when attached or only when Roll Clip
is active.
•
Always Active
— the custom control that
is attached to the source always runs.
•
Follow Roll Clip
— the custom control
that is attached to the source only runs
when Roll Clip is active.
5.
Use the
Postroll
knob to set the amount of
time the switcher will wait before starting
the custom control. When you start a
transition, the switcher performs the
transition and then waits to postroll time
before starting the custom control.
To Assign an On-PST Run CC
Select a custom control to be run when a video
source is selected on both the Program and
Preset bus of the Program ME.
1.
Press
HOME
>
Setup
>
Installation
>
Source
Configuration
>
More
>
More
>
Attach CCs
>
On Air CC
.
2.
Use the
Source
knob to select the video
source that you want to assign a custom
control to.
3.
Use the
Cust Ctrl
knob to select the custom
control you want to run when the selected
source is selected on the preset and program
bus.
Copying and Moving Custom
Controls
Custom controls can be copied, moved, or
swapped with other custom controls on the
switcher. This allows you to duplicate custom
controls on different banks, or re-organize the
custom controls on the same bank.
To Copy or Move a Custom Control
Copy, move, or swap a custom control from the
source location to the destination location.
1.
Press
HOME
>
Custom Controls
>
Copy/Move Macros
.
2.
Press
Source
and use the
Bank
and
Button
knobs to select the custom control that you
want to copy, swap, or move from.
3.
Press
Destination
and use the
Bank
and
Button
knobs to select the custom control
you want to copy, swap, or move to.
4.
Press the
Copy
,
Move
, or
Swap
button to
move or copy the custom control.
•
Copy
— copy the events from the source
custom control to the destination. Both
custom controls will contain the same
events.
Ultrix Acuity Operation Manual (v10.1) — Custom Controls • 85