Ross openGear GPI-8941 Series User Manual Download

Page: 76 / 92

76 • RossTalk Protocol

GPI-8941 User Guide (v9.0)

Sample Session 2

Session assumes that we want to know when GPI 1, 2, and 3 (inputs) go active and controls GPI 17, 18, and 19
(outputs).

GPI 17:off:Event

Card reports that GPI 17 has had an event, this
is the trailing edge

GPI 1:off:Event

Card reports that GPI 1 has had an event. This
input is now inactive/low.

Command

Response

Notes

GPI S:A:OFF

Turn auto-response off

None

No configuration response since auto-response
is off

GPI S:V:OFF

Turn verbose reporting off

None

No configuration response since auto-response
is off

GPI S:B:1

Configure this session to use base 1.

None

No configuration response since auto-response
is off

GPI *:C:N:D

Configure all GPIs to not send GPI change
reports to this session.

None

No configuration response since auto-response
is off

GPI 1:C:L:D:S

Configure GPI 1 to send a detailed report on
leading / rising and trailing / falling edges and
report current GPI status.

GPI 1:0:C

Card replies GPI 1 is off. No configuration
response since auto-response is off.

GPI 2:C:L:D:S

Configure GPI 2 to send a detailed report on
leading / rising and trailing / falling edges and
report current GPI status

GPI 2:0:C

Card replies GPI 2 is off. No configuration
response since auto-response is off.

GPI 3:C:L:D:S

Configure GPI 3 to send a detailed report on
leading / rising and trailing / falling edges and
report current GPI status.

GPI 3:1:C

Card replies GPI 3 is on. No configuration
response since auto-response is off.

GPI 17:C:B:D:S

Configure GPI 17 to send a detailed report on
trailing / falling edges and report current GPI
status

GPI 17:0:C

Card replies GPI 17 is off. No configuration
response since auto-response is off.

GPI 18:C:B:D:S

Configure GPI 18 to send a detailed report on
trailing / falling edges and report current GPI
status.

GPI 18:0:C

Card replies GPI 18 is off. No configuration
response since auto-response is off.

GPI 19:C:B:D:S

Configure GPI 19 to send a detailed report on
trailing / falling edges and report current GPI
status.

Command

Response

Notes

Summary of Contents for openGear GPI-8941 Series





























































































Search results

Summary of Contents for openGear GPI-8941 Series

Reviews:

Related manuals for openGear GPI-8941 Series

Brands by name

Popular brands

Ross openGear GPI-8941 Series, User Manual

Search results

Summary of Contents for openGear GPI-8941 Series

Reviews:

Related manuals for openGear GPI-8941 Series

Brands by name

Popular brands