manualshive.com logo in svg

Ross NK-3G144, User Manual, Page: 7 / 64

Share
Download
Ross NK-3G144 User Manual Download Page 7

NK-3G144 User Guide (v04)

Contents • i

Contents

Introduction 

9

Related Publications.................................................................................................................................................. 9
Documentation Conventions..................................................................................................................................... 9
Contacting Technical Support................................................................................................................................. 10

Before You Begin 

11

Features ................................................................................................................................................................... 11
Typical System Equipment ..................................................................................................................................... 11
System Overview .................................................................................................................................................... 12
How the Panels and Routing Switchers Communicate........................................................................................... 13

Hardware Overview 

15

Front Panel .............................................................................................................................................................. 15
Chassis .................................................................................................................................................................... 16
Cards and Accessories ............................................................................................................................................ 17
Rear Panel ............................................................................................................................................................... 18

Installation 

23

Overview................................................................................................................................................................. 23
Before You Begin ................................................................................................................................................... 23
Unpacking the Equipment....................................................................................................................................... 23
Installing the Routing Switcher .............................................................................................................................. 24
Installing the Routing Switcher System in a Star-Layout....................................................................................... 27
Connecting Source and Destination Devices .......................................................................................................... 31
Connecting a Video Reference to NK Series Routing Switchers ........................................................................... 32
Installing DashBoard .............................................................................................................................................. 32
Connecting to the NK-IPS in the Routing Switcher System .................................................................................. 32
Checking the Firmware Version of a Device.......................................................................................................... 33
Upgrading the Firmware Version of the NK-3G144 ..............................................................................................33

Setting up a Routing Switcher 

35

Implementing Your System Plan ............................................................................................................................ 35
The NK-3G144 Device Tab.................................................................................................................................... 36
Default Configuration ............................................................................................................................................. 37
Setting Up Input Cards............................................................................................................................................ 38
Setting Up Output Cards ......................................................................................................................................... 39
Setting Up Input and Output Offsets ...................................................................................................................... 40
Setting Up Partitions ............................................................................................................................................... 41
Setting Up Video Referencing ................................................................................................................................ 46
Saving the Current File for the Routing Switcher .................................................................................................. 46
Sending a Configuration File to a Device............................................................................................................... 47
SmartPaste............................................................................................................................................................... 48

Operating a Routing Switcher 

49

LED Indicators........................................................................................................................................................ 49
Monitoring the NK-3G144 via DashBoard............................................................................................................. 51
Disabling the Alarm for a PSU ............................................................................................................................... 54
Resetting the NK-3G144......................................................................................................................................... 54
Loading Default Settings ........................................................................................................................................ 54

Summary of Contents for NK-3G144

































































Reviews:

No comments